Quality Control & Product Specification

Product-specific parameters agreed around the buyer’s application and destination market.

Conductivity meter checking a cocopeat sample

Coco coir parameters

Agree EC with its extraction ratio, units and sample preparation; pH, moisture, particle grading, blend ratio, weight and expanded-volume method. VinaTap washed Low EC cocopeat is below 0.4 mS/cm at a 1:1 cocopeat-to-water volume ratio. The supplied cocopeat specification is pH 5.5–6.5 (1:1), moisture below 15% at packing and minimum expansion of 14 L/kg. Confirm hydration and measurement conditions for the selected product.

Before comparing test results, review the cocopeat EC measurement guide. For processing requirements, see washed versus buffered cocopeat and specify washing and buffering separately in your enquiry.

Historical laboratory evidence: sample-specific microbiological results

VinaTap has supplied SGS and Vinacontrol reports for identified cocopeat samples. The results below are historical sample results, separate from current product specifications and from validation of the dryer.

SGS: washed and unwashed cocopeat samples, 2021

Reports 2111080392 (washed Low EC cocopeat) and 2111080393 (unwashed High EC cocopeat), both dated 2 November 2021, record E. coli below 10 CFU/g using ISO 16649-2:2001 and Salmonella spp. not found in the reported 25 g test portion using ISO 6579-1:2017/Amd 1:2020. The uploaded copies show excerpts from pages 1–2 of three-page reports.

Vinacontrol: cocopeat sample, 2023

Certificate of analysis 23G15TND16260-01, dated 17 November 2023, records β-glucuronidase-positive E. coli at 1.0 × 10¹ CFU/g using TCVN 7924-2:2008 (ISO 16649-2:2001). It records Salmonella spp. not detected using TCVN 10780-1:2017 (ISO 6579-1:2017), with a reported eLOD50 of 3 CFU/25 g.

How to use these results

These reports concern the submitted samples and the listed methods. They do not establish that all production is sterile, that mold is absent, or that rotary drying performs better microbiologically than sun drying. The reviewed result pages do not report a mold count or a paired before-and-after drying test.

For an order requiring microbiological acceptance, agree the organisms to test, sample size, test method, laboratory, detection limit, sampling time and lot reference. Request applicable current lot evidence instead of treating historical sample results as a shipment-wide certificate.

Drying process and measurement points

VinaTap reports a biomass-fired stainless-steel rotary dryer, 1.6 m diameter × 22 m length, with readings of 900–1,000°C at the inlet and 100°C at the outlet. The inlet measurement is at the drum entrance in direct contact with incoming wet material, reported at approximately 80% moisture. Dry cocopeat and coco chips are specified at below 15% packing moisture; agree the test method and moisture basis.

The operating-point readings are separate from measured temperatures throughout the material. A validated microbial-reduction claim requires the relevant material time–temperature evidence and microbiological tests. UC Davis heat-treatment guidance explains the importance of temperature distribution and exposure time in potting media.

Read about VinaTap washing, optional buffering and rotary drying or request an agreed processing and testing specification.

Pallet parameters

Dimensions, weight, moisture, static load, dynamic load and design configuration. Published capacity requires the appropriate test evidence.

Biochar parameters

Confirm feedstock, particle grading, moisture, fixed carbon, ash, volatile matter and relevant calorific value with their units, test methods and reporting bases. Request supporting information for the selected grade and intended use; confirm any certification scope separately.

Agreed specifications

Separate target specifications, general reference values and measured batch results. A Technical Data Sheet describes the product; a Certificate of Analysis should identify the lot, values, units and methods tested. Confirm applicable tolerances, sampling, inspection and recheck arrangements before ordering.

Review your product and shipment

Cocopeat specifications · Pallet design and tested loads · Biochar grades · Shipment documents

Let’s discuss your specification.

Request a Quote
WhatsApp Factory